EXTERIOR COATINGS AND PAINTS

• Excellent chemical resistance and UV resistance
• Excellent adhesion to many surfaces
• Abrasion-resistant film
• Equally effective on concrete or metal substrates
• Perfect material for coatings of MS pipelines and structural steel

• Free the surface to be coated from dust, oil, moisture, grease, etc
• The surface should be completely dry
• Stir the contents of part A well
• Mix 4 parts by volume of part A with 1 part by volume of part B
• Stir well to get homogeneity
• Allow the mixture to stand still for about 10-15 min to initiate the reaction
• Apply using a spray or brush
• Allow the coat to cure for 2 hrs before re-coating
• After applying the second coat, allow it to heal 24 hrs

• Tough abrasion, chemical-resistant film
• Excellent adhesion to many surfaces, including concrete and metal substrates

• Free the surface to be coated from dust, oil, moisture, grease, etc
• The surface should be completely dry
• Stir the contents of part A well
• Mix 2 parts of part A with 1 part of part B
• Stir well to get homogeneity
• Allow the mixture to stand still for about 10-15 min to initiate the reaction
• Apply using a spray or brush
• Allow the coat to cure for 2 hrs before re-coating

• Protects the structures from water leakages or dampness
• Prevents a rise in internal temperature
• It does not peel or crack
• Prevents carbonation
• Prevents the formation of fungi and algae
• Has UV protection

• Stir the contents well with a mechanical stirrer to attain uniform consistency
• Add 500 ml of potable water to 1 litre of SUNEXT-8 in a clean container
• Apply by brush, roller, or spray as a primer coat
• Depending on the recommendations, subsequently, apply 2/3 coats
• Maintain a minimum interval of 4-6 hours between successive coats

• It does not peel or crack
• Good resistance to weathering
• Resists the formation of algae & fungus
• No carbonation deposits
• Increases the total service life of the structure
• UV resistant
• Reduces maintenance cost

• Stir the contents well with a mechanical stirrer to attain uniform consistency
• Add 400 ml of water to one litre of SUNEXT-S & apply as a primer coat by brush, roller, or spray
• Allow the primer coat to dry and set for 4-6 hours
• Apply 2-3 coats of SUNEXT-S directly without the addition of water,
• Apply it at an interval of 6 hours between each coat
• For ease of application, if required, add little water but not more than 100 ml per Litre of SUNEXT-S
• After the final coat, allow it to sit for 24 hours
• During the entire application & set period, protect the coating from dust, dirt, water, etc

• It does not peel or crack
• Protects from water leakages
• No damp spots
• Resists the formation of algae & fungus
• No carbonation deposits, resulting in a fresh look of the coating for years
• Thus, it increases the total service life of the structure with reduced maintenance cost per year

• Stir the contents thoroughly with a mechanical stirrer to attain uniform consistency
• Depending on the recommendations, apply two or three coats of SUNDEKOTE-SP directly
• Apply it at an interval of 8-10 hours between each coat
• After the final coat, allow it to set for 24 hours

• Single-component liquid applied by brush
• Protects against water leakages and dampness
• Prevents rise in internal temperature
• No peeling or cracking
• Prevents the formation of fungi and algae
• Excellent UV stability
• Fairly good resistance to normal wear and tear
• No priming coat is needed, saving expenses and time.

Surface Preparation & Cleaning:

• Life and performance depend on cleaning quality.
• Remove dirt, loose particles, flaking paint, etc.
• Check for cracks or openings.
• Fill cracks with POLYFILL AR; use POLYALK EP for specialised cracks.
• Remove scales, rust, and grease from steel surfaces.

Application:

• Open the container, and stir well for uniform consistency.
• For the prime coat, mix 1L SUNACE with 1000ml water. Apply by brush, roller, or spray.
• For the top coat, mix 1L SUNACE with 400ml water. Stir well.
• Apply by brush, roller, or spray.
• Apply two or three coats over the prime coat as recommended.
• Maintain 4-6 hour intervals between coats.
• During the entire application

• Adheres firmly to new/old hardened concrete surfaces
• Hides plaster cracks due to excellent flexibility & elasticity
• It makes the surface waterproof, resistant to fungal attack and carbonation
• Acts as fire-retardant

• Stir the contents with a stirrer to attain uniform consistency
• If required, add 5-10% water by volume to get an easily spreadable consistency
• Apply POLYTEXT FINISH using a flat trowel at a thickness of 2-3 mm
• Repeat the trowel on the spread material in one direction only till the desired finish is obtained
• Remove excess POLYTEXT FINISH with a damp cloth before the material sets
• Cure for 12-16 hours minimum before application of any exterior paint

• Excellent flexibility and durability
• Excellent weatherproofing properties thus protect from wind and rain
• Resistant to algae, fungus, dirt, and mildew
• Easy to apply, economical, environmentally safe
• High resistance to UV radiation
• Bridges cracks and hides imperfections

• Clean the surface with a wire brush, or any other suitable method
• Fill the cracks with crack filler like POLYFILL AR
• For large cracks, use POLYALK EP mortar
• Mix one litre of SUNEXT 8 with one litre of water and apply as a primer coat
• Allow it to dry for 6-8 hrs
• Open the container of DUCKBACK S and stir well to attain uniform consistency
• Apply 2 coats without dilution by brush or roller with an interval of 6-8 hours between each coat

• Miscible with water, easy to handle
• Treats and controls fungal and bacterial growth
• Non-toxic to human beings
• Non-corrosive
• Treats and controls the roots of plants

For a microbial wall wash

• On vertical walls, a 5% aqueous solution of SUNANTIFUNGAL SP is to be used as micro-bio-wash
• Allow it to remain in contact for about 10 minutes, then scrubbing may be required
• Wash with fresh water to remove loosened microbial deposits
• Allow drying before painting

For sanitation in dairies, hospitals, and food industries

• Use a 2% aqueous solution of SUNANTIFUNGAL SP
• Follow all steps for a microbial wall wash

For anti-rooting treatment of plants

• Mix 30% - 40% anti-rooting solution in water homogeneously
• Apply 3 coats by maintaining 4 - 5 hrs time intervals
• Complete the application before earth filling